Making a 3D Paper Rose

I recently purchased the McGill Paper Blossoms tool set at the Scrapbook Convention I went to. Last night I tried out the tools with some paper flowers I die cut using my Donna Salazar Rose Creations Die by Spellbinders  . Click the highlited link to find the die template set at my store. I also have the Donna Salazar video in the item description. After I made these flowers I went on YouTube and found a video by Donna Salazar herself showing a couple of ways you can use her die. I’m telling you, this is a die you are going to want! It even comes with 3 different sized leaves. I have a tutorial below, but read the whole thing first! I tell you a couple of things that I would improve and do different the next time I make one of these.

Here are the supplies I used:

•McGill Paper Blossoms Tool Set
•Foam Pad to shape the flower on ( I folded a piece of kid craft foam in half. Worked just fine)
Spellbinders Rose Creation Die Set
•Big Shot or other die cutting machine that works with Spellbinders wafer-thin dies.
•Patterned Paper (mine was from a Recollections Paper Pad)
•Distress Inks (one in a color to match the flower part and another to match the leaves)
•Cosmetic Sponge or Ink Blending Tool
•Paper Piercer ( You will need this to pop the pieces out of the dies and poke the little hole out of the middle when it is stuck in the die)
•Glossy Accents (or other quick drying clear glue)
•Non-Stick Craft Mat (or work on a space you don’t mind getting inky)
•Metal Brad and Alcohol Ink (Or a brad that you like and don’t need to color with Alcohol Inks)

Ok! That looks like a ton of supplies, but hopefully you already have a lot of that stuff.

Wait…where did those come from?! LOL. I walked in my craft room the other day and found these beautiful flowers and two bags of my favorite chocolate truffles. He gave them to me for no reason! I couldn’t believe it and I was so blown away. It made me feel so special. I had to share!

Ok back to the project haha!

Here are some of the supplies I started with. I  ended up only die cutting less than half of this paper out. Running that die through the machine time and time again gets a little boring. Besides, I started to get a neck ache! You actually just need to run the full set through once to be able to make a flower. I just kept running it through with different colors since I plan to make a ton of these to put on Mother’s Day Cards.

I cut down the papers and ran them through the Big Shot.

Here are the piles I ended up with when I was done with all the cutting. I haven’t tried the vellum yet, but I definitely plan to! After I die cut all of these out I inked up the edges with a distress ink that closely matched the color using half of a cosmetic sponge. I did that to the leaves too. The next step was forming.

This is the part that would probably be easier to follow on a video. There actually is a video by McGill on YouTube showing how to make the paper flowers using their punches. I used a few of the techniques I learned from the video, but I had to modify them to use my dies instead. Basically what I am showing here is that I took the tip and swirled it around in a circle around the hole in the middle. I also swirled it around in circles on each petal. This apparently breaks up the fibers, but it also makes it start to shape and lift.

I repeated this with each size flower and slowly moved down the size of the ball point from 8mm to 6mm to 5mm to 3mm as I was getting to the smaller flowers. The picture below shows what it looks like at this point.

.

.

.

If you like this look , you can actually just stop here and put a brad through it. If I was to stop here and use the flower just like this I would, however, add another one of the largest flower layers and curl up a small one for the middle. I would also still add the leaves to it. If you want it to be even more dimensional, you can add glue to the bases of each part and glue them together. That will force them to be tighter and more 3D. Donna Salazar shows that in her video about this die set.

The next step involves taking the tweezers out of the tool set and putting it through the hole to clamp on to the middle of each petal. You then take your thumb and forefinger and form the petal around the tweezers. Do this to each and every petal if you want to get this different look I will show in the end. You also take the tweezers and bend each side of the petal down. This part is really easy and doesn’t take that long.

This picture shows what the flower looked like after I completed the bending. The leaves were done the same way I did the petals. I first swirled around on them with the 8mm ball point then I bent the ends. One the leaves I also took a very small pointed tool and made a line down the middle. I am not sure if you can really see that though.

Next, I just put a little Glossy Accents on the bottoms of each flower piece and stacked them up. Pretty Simple. You could use hot glue for this part instead if you want.

Here is what it looked like after gluing was done.

I decided that I didn’t like how wide the opening was so I used another one of the smallest flowers. The paper I used was not double-sided so I had to use a mixture of my pigment inks and distress inks to try imitating the patterned paper. When I make these again I will either make sure I can imitate the paper well or just use double-sided paper. I overlapped and glued the petals together to get a tight bud for the middle. I did not glue the last petal to the first just because I wanted it to look like that. It is up to you how you decide to glue it together though. I glued the small bud to the middle of the flower using Glossy Accents again.

I wanted my middle metal brad to kind of match the flower so I took a silver brad and dyed it with Adirondack Alcohol Inks. It didn’t take too long to dry. Be careful though because I didn’t realize that I should have dabbed out the ink stuck under the bottom of the top part of the brad. There was some in there and it got on my flower as I was lowering it in. Oops!

Finished!

All the pictures just above are of the finished flower . Hopefully you were able to follow my odd instructions. If you need or want a video, just let me know! I wasn’t comfortable with doing a video the first time since I didn’t know at all what I was doing, but now I think I could do it.

Next time I make these flowers I will use more layers  like 2-3 of some of the same sizes for more fullness. I will also probably use double-sided paper.

Thanks for stopping by! Don’t forget to comment 🙂

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s